How To Repair Cracks In A Mobile Home Bathtub

As a full general rule, replacing a bathtub is NOT considered a do-it-yourself project — especially if you lot are irresolute the blazon and size of the tub. Changing annihilation ways refiguring the bleed lines, vents, and waterlines and that tin go a bit tricky and frustrating. Simply if your former tub is cracked or damaged and you simply wish to replace it with the same kind, and then the project becomes more manageable.

Should You Repair or Supervene upon Your Mobile Home Bath Tub?

Most bathtubs in mobile homes are plastic. When plastic cracks or breaks, it cannot exist permanently repaired like fiberglass can. If the crack isn't besides bad, the best you lot tin practice is temporarily repair information technology by using one of ii methods.

The get-go method is to purchase an epoxy repair kit. The biggest reward of the epoxy kit is that the repair isn't as noticeable considering the colour somewhat matches the tub. The disadvantage is that it works all-time merely on pocket-size cracks because any motion on big cracks can crusade the cleft to reappear.

The 2nd method to repair a cracked plastic bathtub is to apply a slice of quick set tub repair record to seal the crevice. The advantage of the record is that it volition move with the tub so the fissure volition not reappear (unless the cleft runs). The disadvantage is that it looks somewhat gaudy merely by gosh it does piece of work!

Bathtub Facts

If yous've decided to replace your bathtub, besides the size and colour you will also want to sympathize how and why the bottom of your tub is supported. Most plastic tubs are supported in two means — plastic legs or styrofoam.

Pictured is a tub supported by plastic legs. If you accept a sewer pipe running straight nether the tub, then you will need this type of tub to make room for the pipes. The disadvantage of using a tub with legs is that the tub can creak if the subfloor under the tub isn't apartment causing the legs to sit uneven. The legs take to installed into the bottom of the tub. When doing and then, push button them in direct or you lot'll risk breaking a tab that holds the legs in.

The next photo shows a tub that uses styrofoam for support rather than plastic legs. The styrofoam sits directly onto the flooring. Overall, the styrofoam offers improve support with fashion less creaks. Obviously, the disadvantage is that you tin't run pipes directly nether the tub.

Removal of Quondam Tub and Surround

First close off water to the bathtub. From underneath the tub, unscrew pipes from drain. This can be accomplished past either taking autonomously the p-trap (higher up) or unscrewing the pipe directly from the tub bleed itself. If your tub has an overflow, at that place will exist another pipe going up the back of the tub to the overflow. In this case simply have autonomously the p-trap and the balance will come out with the tub.

Again, exist sure the water is shut off to the tub. Side by side unscrew the waterline connections from the dorsum of the faucet. Remove the nuts from the hot and cold nipples and slide the faucet out. Older faucets can be much more complicated to remove as the faucets themselves may have to be disassembled along with the spout and shower caput.

In one case the faucet is removed, next footstep is to become rid of the old tub surround. If the old tub surround is held in place with plastic rivets, cut off the head with a knife or drill them out. And so with a utility knife, cut around the edge of the tub surround to loosen the caulk. Finally, take hold of a corner of the environment and advisedly pull information technology off the wall.

With the tub surroundings removed, the lip of the tub will be exposed. Remove all the screws from this lip.

The erstwhile bathtub should at present be loose and able to be lifted out and removed from the bathroom.

Installed admission door showing a peak at the main close-off backside it.

Prep for the New Bathtub

Prepare the opening for the tub. First be sure that the rim back up boards are set at the proper height for the new tub. Use boards longer than what's shown in the analogy in a higher place. Gear up level and secure into the studs of the wall.

Almost likely your old tub had a brim track fastened to the flooring. This helps stiffen up the skirt on the tub. If the old skirt track is in good shape, leave it. Otherwise, supercede it with the one that probably came with the new tub.

Nothing is more frustrating than having a water leak after the new tub is installed. The best mode to head-off a leak is to install a new drain, faucet and waterline ends. Become rid of the old parts — in one case removed they may never seal correct again so beginning with new. More than info on obtaining and installing the right drain assembly tin can be found hither.

Source: https://www.mobilehomerepair.com/replace-repair-mobile-home-bathtub/

Posted by: fantneative.blogspot.com

Share this post